Initial commit: Linux kernel 4.19 for Unplugged OS

This commit is contained in:
ziv committed 2025-10-06 13:52:42 +00:00
commit d30235b04c
80519 files changed
+35800681

No files matched your search

+38
View File
@@ -0,0 +1,38 @@
PowerNow! and Cool'n'Quiet are AMD names for frequency
management capabilities in AMD processors. As the hardware
implementation changes in new generations of the processors,
there is a different cpu-freq driver for each generation.
Note that the driver's will not load on the "wrong" hardware,
so it is safe to try each driver in turn when in doubt as to
which is the correct driver.
Note that the functionality to change frequency (and voltage)
is not available in all processors. The drivers will refuse
to load on processors without this capability. The capability
is detected with the cpuid instruction.
The drivers use BIOS supplied tables to obtain frequency and
voltage information appropriate for a particular platform.
Frequency transitions will be unavailable if the BIOS does
not supply these tables.
6th Generation: powernow-k6
7th Generation: powernow-k7: Athlon, Duron, Geode.
8th Generation: powernow-k8: Athlon, Athlon 64, Opteron, Sempron.
Documentation on this functionality in 8th generation processors
is available in the "BIOS and Kernel Developer's Guide", publication
26094, in chapter 9, available for download from www.amd.com.
BIOS supplied data, for powernow-k7 and for powernow-k8, may be
from either the PSB table or from ACPI objects. The ACPI support
is only available if the kernel config sets CONFIG_ACPI_PROCESSOR.
The powernow-k8 driver will attempt to use ACPI if so configured,
and fall back to PST if that fails.
The powernow-k7 driver will try to use the PSB support first, and
fall back to ACPI if the PSB support fails. A module parameter,
acpi_force, is provided to force ACPI support to be used instead
of PSB support.
+120
View File
@@ -0,0 +1,120 @@
CPU frequency and voltage scaling code in the Linux(TM) kernel
L i n u x C P U F r e q
C P U F r e q C o r e
Dominik Brodowski <linux@brodo.de>
David Kimdon <dwhedon@debian.org>
Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar <viresh.kumar@linaro.org>
Clock scaling allows you to change the clock speed of the CPUs on the
fly. This is a nice method to save battery power, because the lower
the clock speed, the less power the CPU consumes.
Contents:
---------
1. CPUFreq core and interfaces
2. CPUFreq notifiers
3. CPUFreq Table Generation with Operating Performance Point (OPP)
1. General Information
=======================
The CPUFreq core code is located in drivers/cpufreq/cpufreq.c. This
cpufreq code offers a standardized interface for the CPUFreq
architecture drivers (those pieces of code that do actual
frequency transitions), as well as to "notifiers". These are device
drivers or other part of the kernel that need to be informed of
policy changes (ex. thermal modules like ACPI) or of all
frequency changes (ex. timing code) or even need to force certain
speed limits (like LCD drivers on ARM architecture). Additionally, the
kernel "constant" loops_per_jiffy is updated on frequency changes
here.
Reference counting of the cpufreq policies is done by cpufreq_cpu_get
and cpufreq_cpu_put, which make sure that the cpufreq driver is
correctly registered with the core, and will not be unloaded until
cpufreq_put_cpu is called. That also ensures that the respective cpufreq
policy doesn't get freed while being used.
2. CPUFreq notifiers
====================
CPUFreq notifiers conform to the standard kernel notifier interface.
See linux/include/linux/notifier.h for details on notifiers.
There are two different CPUFreq notifiers - policy notifiers and
transition notifiers.
2.1 CPUFreq policy notifiers
----------------------------
These are notified when a new policy is intended to be set. Each
CPUFreq policy notifier is called twice for a policy transition:
1.) During CPUFREQ_ADJUST all CPUFreq notifiers may change the limit if
they see a need for this - may it be thermal considerations or
hardware limitations.
2.) And during CPUFREQ_NOTIFY all notifiers are informed of the new policy
- if two hardware drivers failed to agree on a new policy before this
stage, the incompatible hardware shall be shut down, and the user
informed of this.
The phase is specified in the second argument to the notifier.
The third argument, a void *pointer, points to a struct cpufreq_policy
consisting of several values, including min, max (the lower and upper
frequencies (in kHz) of the new policy).
2.2 CPUFreq transition notifiers
--------------------------------
These are notified twice for each online CPU in the policy, when the
CPUfreq driver switches the CPU core frequency and this change has no
any external implications.
The second argument specifies the phase - CPUFREQ_PRECHANGE or
CPUFREQ_POSTCHANGE.
The third argument is a struct cpufreq_freqs with the following
values:
cpu - number of the affected CPU
old - old frequency
new - new frequency
flags - flags of the cpufreq driver
3. CPUFreq Table Generation with Operating Performance Point (OPP)
==================================================================
For details about OPP, see Documentation/power/opp.txt
dev_pm_opp_init_cpufreq_table -
This function provides a ready to use conversion routine to translate
the OPP layer's internal information about the available frequencies
into a format readily providable to cpufreq.
WARNING: Do not use this function in interrupt context.
Example:
soc_pm_init()
{
/* Do things */
r = dev_pm_opp_init_cpufreq_table(dev, &freq_table);
if (!r)
policy->freq_table = freq_table;
/* Do other things */
}
NOTE: This function is available only if CONFIG_CPU_FREQ is enabled in
addition to CONFIG_PM_OPP.
dev_pm_opp_free_cpufreq_table - Free up the table allocated by dev_pm_opp_init_cpufreq_table
+295
View File
@@ -0,0 +1,295 @@
CPU frequency and voltage scaling code in the Linux(TM) kernel
L i n u x C P U F r e q
C P U D r i v e r s
- information for developers -
Dominik Brodowski <linux@brodo.de>
Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar <viresh.kumar@linaro.org>
Clock scaling allows you to change the clock speed of the CPUs on the
fly. This is a nice method to save battery power, because the lower
the clock speed, the less power the CPU consumes.
Contents:
---------
1. What To Do?
1.1 Initialization
1.2 Per-CPU Initialization
1.3 verify
1.4 target/target_index or setpolicy?
1.5 target/target_index
1.6 setpolicy
1.7 get_intermediate and target_intermediate
2. Frequency Table Helpers
1. What To Do?
==============
So, you just got a brand-new CPU / chipset with datasheets and want to
add cpufreq support for this CPU / chipset? Great. Here are some hints
on what is necessary:
1.1 Initialization
------------------
First of all, in an __initcall level 7 (module_init()) or later
function check whether this kernel runs on the right CPU and the right
chipset. If so, register a struct cpufreq_driver with the CPUfreq core
using cpufreq_register_driver()
What shall this struct cpufreq_driver contain?
.name - The name of this driver.
.init - A pointer to the per-policy initialization function.
.verify - A pointer to a "verification" function.
.setpolicy _or_ .fast_switch _or_ .target _or_ .target_index - See
below on the differences.
And optionally
.flags - Hints for the cpufreq core.
.driver_data - cpufreq driver specific data.
.resolve_freq - Returns the most appropriate frequency for a target
frequency. Doesn't change the frequency though.
.get_intermediate and target_intermediate - Used to switch to stable
frequency while changing CPU frequency.
.get - Returns current frequency of the CPU.
.bios_limit - Returns HW/BIOS max frequency limitations for the CPU.
.exit - A pointer to a per-policy cleanup function called during
CPU_POST_DEAD phase of cpu hotplug process.
.stop_cpu - A pointer to a per-policy stop function called during
CPU_DOWN_PREPARE phase of cpu hotplug process.
.suspend - A pointer to a per-policy suspend function which is called
with interrupts disabled and _after_ the governor is stopped for the
policy.
.resume - A pointer to a per-policy resume function which is called
with interrupts disabled and _before_ the governor is started again.
.ready - A pointer to a per-policy ready function which is called after
the policy is fully initialized.
.attr - A pointer to a NULL-terminated list of "struct freq_attr" which
allow to export values to sysfs.
.boost_enabled - If set, boost frequencies are enabled.
.set_boost - A pointer to a per-policy function to enable/disable boost
frequencies.
1.2 Per-CPU Initialization
--------------------------
Whenever a new CPU is registered with the device model, or after the
cpufreq driver registers itself, the per-policy initialization function
cpufreq_driver.init is called if no cpufreq policy existed for the CPU.
Note that the .init() and .exit() routines are called only once for the
policy and not for each CPU managed by the policy. It takes a struct
cpufreq_policy *policy as argument. What to do now?
If necessary, activate the CPUfreq support on your CPU.
Then, the driver must fill in the following values:
policy->cpuinfo.min_freq _and_
policy->cpuinfo.max_freq - the minimum and maximum frequency
(in kHz) which is supported by
this CPU
policy->cpuinfo.transition_latency the time it takes on this CPU to
switch between two frequencies in
nanoseconds (if appropriate, else
specify CPUFREQ_ETERNAL)
policy->cur The current operating frequency of
this CPU (if appropriate)
policy->min,
policy->max,
policy->policy and, if necessary,
policy->governor must contain the "default policy" for
this CPU. A few moments later,
cpufreq_driver.verify and either
cpufreq_driver.setpolicy or
cpufreq_driver.target/target_index is called
with these values.
policy->cpus Update this with the masks of the
(online + offline) CPUs that do DVFS
along with this CPU (i.e. that share
clock/voltage rails with it).
For setting some of these values (cpuinfo.min[max]_freq, policy->min[max]), the
frequency table helpers might be helpful. See the section 2 for more information
on them.
1.3 verify
----------
When the user decides a new policy (consisting of
"policy,governor,min,max") shall be set, this policy must be validated
so that incompatible values can be corrected. For verifying these
values cpufreq_verify_within_limits(struct cpufreq_policy *policy,
unsigned int min_freq, unsigned int max_freq) function might be helpful.
See section 2 for details on frequency table helpers.
You need to make sure that at least one valid frequency (or operating
range) is within policy->min and policy->max. If necessary, increase
policy->max first, and only if this is no solution, decrease policy->min.
1.4 target or target_index or setpolicy or fast_switch?
-------------------------------------------------------
Most cpufreq drivers or even most cpu frequency scaling algorithms
only allow the CPU frequency to be set to predefined fixed values. For
these, you use the ->target(), ->target_index() or ->fast_switch()
callbacks.
Some cpufreq capable processors switch the frequency between certain
limits on their own. These shall use the ->setpolicy() callback.
1.5. target/target_index
------------------------
The target_index call has two arguments: struct cpufreq_policy *policy,
and unsigned int index (into the exposed frequency table).
The CPUfreq driver must set the new frequency when called here. The
actual frequency must be determined by freq_table[index].frequency.
It should always restore to earlier frequency (i.e. policy->restore_freq) in
case of errors, even if we switched to intermediate frequency earlier.
Deprecated:
----------
The target call has three arguments: struct cpufreq_policy *policy,
unsigned int target_frequency, unsigned int relation.
The CPUfreq driver must set the new frequency when called here. The
actual frequency must be determined using the following rules:
- keep close to "target_freq"
- policy->min <= new_freq <= policy->max (THIS MUST BE VALID!!!)
- if relation==CPUFREQ_REL_L, try to select a new_freq higher than or equal
target_freq. ("L for lowest, but no lower than")
- if relation==CPUFREQ_REL_H, try to select a new_freq lower than or equal
target_freq. ("H for highest, but no higher than")
Here again the frequency table helper might assist you - see section 2
for details.
1.6. fast_switch
----------------
This function is used for frequency switching from scheduler's context.
Not all drivers are expected to implement it, as sleeping from within
this callback isn't allowed. This callback must be highly optimized to
do switching as fast as possible.
This function has two arguments: struct cpufreq_policy *policy and
unsigned int target_frequency.
1.7 setpolicy
-------------
The setpolicy call only takes a struct cpufreq_policy *policy as
argument. You need to set the lower limit of the in-processor or
in-chipset dynamic frequency switching to policy->min, the upper limit
to policy->max, and -if supported- select a performance-oriented
setting when policy->policy is CPUFREQ_POLICY_PERFORMANCE, and a
powersaving-oriented setting when CPUFREQ_POLICY_POWERSAVE. Also check
the reference implementation in drivers/cpufreq/longrun.c
1.8 get_intermediate and target_intermediate
--------------------------------------------
Only for drivers with target_index() and CPUFREQ_ASYNC_NOTIFICATION unset.
get_intermediate should return a stable intermediate frequency platform wants to
switch to, and target_intermediate() should set CPU to that frequency, before
jumping to the frequency corresponding to 'index'. Core will take care of
sending notifications and driver doesn't have to handle them in
target_intermediate() or target_index().
Drivers can return '0' from get_intermediate() in case they don't wish to switch
to intermediate frequency for some target frequency. In that case core will
directly call ->target_index().
NOTE: ->target_index() should restore to policy->restore_freq in case of
failures as core would send notifications for that.
2. Frequency Table Helpers
==========================
As most cpufreq processors only allow for being set to a few specific
frequencies, a "frequency table" with some functions might assist in
some work of the processor driver. Such a "frequency table" consists of
an array of struct cpufreq_frequency_table entries, with driver specific
values in "driver_data", the corresponding frequency in "frequency" and
flags set. At the end of the table, you need to add a
cpufreq_frequency_table entry with frequency set to CPUFREQ_TABLE_END.
And if you want to skip one entry in the table, set the frequency to
CPUFREQ_ENTRY_INVALID. The entries don't need to be in sorted in any
particular order, but if they are cpufreq core will do DVFS a bit
quickly for them as search for best match is faster.
The cpufreq table is verified automatically by the core if the policy contains a
valid pointer in its policy->freq_table field.
cpufreq_frequency_table_verify() assures that at least one valid
frequency is within policy->min and policy->max, and all other criteria
are met. This is helpful for the ->verify call.
cpufreq_frequency_table_target() is the corresponding frequency table
helper for the ->target stage. Just pass the values to this function,
and this function returns the of the frequency table entry which
contains the frequency the CPU shall be set to.
The following macros can be used as iterators over cpufreq_frequency_table:
cpufreq_for_each_entry(pos, table) - iterates over all entries of frequency
table.
cpufreq_for_each_valid_entry(pos, table) - iterates over all entries,
excluding CPUFREQ_ENTRY_INVALID frequencies.
Use arguments "pos" - a cpufreq_frequency_table * as a loop cursor and
"table" - the cpufreq_frequency_table * you want to iterate over.
For example:
struct cpufreq_frequency_table *pos, *driver_freq_table;
cpufreq_for_each_entry(pos, driver_freq_table) {
/* Do something with pos */
pos->frequency = ...
}
If you need to work with the position of pos within driver_freq_table,
do not subtract the pointers, as it is quite costly. Instead, use the
macros cpufreq_for_each_entry_idx() and cpufreq_for_each_valid_entry_idx().
@@ -0,0 +1,19 @@
The cpufreq-nforce2 driver changes the FSB on nVidia nForce2 platforms.
This works better than on other platforms, because the FSB of the CPU
can be controlled independently from the PCI/AGP clock.
The module has two options:
fid: multiplier * 10 (for example 8.5 = 85)
min_fsb: minimum FSB
If not set, fid is calculated from the current CPU speed and the FSB.
min_fsb defaults to FSB at boot time - 50 MHz.
IMPORTANT: The available range is limited downwards!
Also the minimum available FSB can differ, for systems
booting with 200 MHz, 150 should always work.
+125
View File
@@ -0,0 +1,125 @@
CPU frequency and voltage scaling statistics in the Linux(TM) kernel
L i n u x c p u f r e q - s t a t s d r i v e r
- information for users -
Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Contents
1. Introduction
2. Statistics Provided (with example)
3. Configuring cpufreq-stats
1. Introduction
cpufreq-stats is a driver that provides CPU frequency statistics for each CPU.
These statistics are provided in /sysfs as a bunch of read_only interfaces. This
interface (when configured) will appear in a separate directory under cpufreq
in /sysfs (<sysfs root>/devices/system/cpu/cpuX/cpufreq/stats/) for each CPU.
Various statistics will form read_only files under this directory.
This driver is designed to be independent of any particular cpufreq_driver
that may be running on your CPU. So, it will work with any cpufreq_driver.
2. Statistics Provided (with example)
cpufreq stats provides following statistics (explained in detail below).
- time_in_state
- total_trans
- trans_table
All the statistics will be from the time the stats driver has been inserted
(or the time the stats were reset) to the time when a read of a particular
statistic is done. Obviously, stats driver will not have any information
about the frequency transitions before the stats driver insertion.
--------------------------------------------------------------------------------
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # ls -l
total 0
drwxr-xr-x 2 root root 0 May 14 16:06 .
drwxr-xr-x 3 root root 0 May 14 15:58 ..
--w------- 1 root root 4096 May 14 16:06 reset
-r--r--r-- 1 root root 4096 May 14 16:06 time_in_state
-r--r--r-- 1 root root 4096 May 14 16:06 total_trans
-r--r--r-- 1 root root 4096 May 14 16:06 trans_table
--------------------------------------------------------------------------------
- reset
Write-only attribute that can be used to reset the stat counters. This can be
useful for evaluating system behaviour under different governors without the
need for a reboot.
- time_in_state
This gives the amount of time spent in each of the frequencies supported by
this CPU. The cat output will have "<frequency> <time>" pair in each line, which
will mean this CPU spent <time> usertime units of time at <frequency>. Output
will have one line for each of the supported frequencies. usertime units here
is 10mS (similar to other time exported in /proc).
--------------------------------------------------------------------------------
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat time_in_state
3600000 2089
3400000 136
3200000 34
3000000 67
2800000 172488
--------------------------------------------------------------------------------
- total_trans
This gives the total number of frequency transitions on this CPU. The cat
output will have a single count which is the total number of frequency
transitions.
--------------------------------------------------------------------------------
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat total_trans
20
--------------------------------------------------------------------------------
- trans_table
This will give a fine grained information about all the CPU frequency
transitions. The cat output here is a two dimensional matrix, where an entry
<i,j> (row i, column j) represents the count of number of transitions from
Freq_i to Freq_j. Freq_i is in descending order with increasing rows and
Freq_j is in descending order with increasing columns. The output here also
contains the actual freq values for each row and column for better readability.
If the transition table is bigger than PAGE_SIZE, reading this will
return an -EFBIG error.
--------------------------------------------------------------------------------
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat trans_table
From : To
: 3600000 3400000 3200000 3000000 2800000
3600000: 0 5 0 0 0
3400000: 4 0 2 0 0
3200000: 0 1 0 2 0
3000000: 0 0 1 0 3
2800000: 0 0 0 2 0
--------------------------------------------------------------------------------
3. Configuring cpufreq-stats
To configure cpufreq-stats in your kernel
Config Main Menu
Power management options (ACPI, APM) --->
CPU Frequency scaling --->
[*] CPU Frequency scaling
[*] CPU frequency translation statistics
"CPU Frequency scaling" (CONFIG_CPU_FREQ) should be enabled to configure
cpufreq-stats.
"CPU frequency translation statistics" (CONFIG_CPU_FREQ_STAT) provides the
statistics which includes time_in_state, total_trans and trans_table.
Once this option is enabled and your CPU supports cpufrequency, you
will be able to see the CPU frequency statistics in /sysfs.
+56
View File
@@ -0,0 +1,56 @@
CPU frequency and voltage scaling code in the Linux(TM) kernel
L i n u x C P U F r e q
Dominik Brodowski <linux@brodo.de>
Clock scaling allows you to change the clock speed of the CPUs on the
fly. This is a nice method to save battery power, because the lower
the clock speed, the less power the CPU consumes.
Documents in this directory:
----------------------------
amd-powernow.txt - AMD powernow driver specific file.
core.txt - General description of the CPUFreq core and
of CPUFreq notifiers.
cpu-drivers.txt - How to implement a new cpufreq processor driver.
cpufreq-nforce2.txt - nVidia nForce2 platform specific file.
cpufreq-stats.txt - General description of sysfs cpufreq stats.
index.txt - File index, Mailing list and Links (this document)
pcc-cpufreq.txt - PCC cpufreq driver specific file.
Mailing List
------------
There is a CPU frequency changing CVS commit and general list where
you can report bugs, problems or submit patches. To post a message,
send an email to linux-pm@vger.kernel.org.
Links
-----
the FTP archives:
* ftp://ftp.linux.org.uk/pub/linux/cpufreq/
how to access the CVS repository:
* http://cvs.arm.linux.org.uk/
the CPUFreq Mailing list:
* http://vger.kernel.org/vger-lists.html#linux-pm
Clock and voltage scaling for the SA-1100:
* http://www.lartmaker.nl/projects/scaling
+207
View File
@@ -0,0 +1,207 @@
/*
* pcc-cpufreq.txt - PCC interface documentation
*
* Copyright (C) 2009 Red Hat, Matthew Garrett <mjg@redhat.com>
* Copyright (C) 2009 Hewlett-Packard Development Company, L.P.
* Nagananda Chumbalkar <nagananda.chumbalkar@hp.com>
*
* ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or NON
* INFRINGEMENT. See the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*
* ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
*/
Processor Clocking Control Driver
---------------------------------
Contents:
---------
1. Introduction
1.1 PCC interface
1.1.1 Get Average Frequency
1.1.2 Set Desired Frequency
1.2 Platforms affected
2. Driver and /sys details
2.1 scaling_available_frequencies
2.2 cpuinfo_transition_latency
2.3 cpuinfo_cur_freq
2.4 related_cpus
3. Caveats
1. Introduction:
----------------
Processor Clocking Control (PCC) is an interface between the platform
firmware and OSPM. It is a mechanism for coordinating processor
performance (ie: frequency) between the platform firmware and the OS.
The PCC driver (pcc-cpufreq) allows OSPM to take advantage of the PCC
interface.
OS utilizes the PCC interface to inform platform firmware what frequency the
OS wants for a logical processor. The platform firmware attempts to achieve
the requested frequency. If the request for the target frequency could not be
satisfied by platform firmware, then it usually means that power budget
conditions are in place, and "power capping" is taking place.
1.1 PCC interface:
------------------
The complete PCC specification is available here:
http://www.acpica.org/download/Processor-Clocking-Control-v1p0.pdf
PCC relies on a shared memory region that provides a channel for communication
between the OS and platform firmware. PCC also implements a "doorbell" that
is used by the OS to inform the platform firmware that a command has been
sent.
The ACPI PCCH() method is used to discover the location of the PCC shared
memory region. The shared memory region header contains the "command" and
"status" interface. PCCH() also contains details on how to access the platform
doorbell.
The following commands are supported by the PCC interface:
* Get Average Frequency
* Set Desired Frequency
The ACPI PCCP() method is implemented for each logical processor and is
used to discover the offsets for the input and output buffers in the shared
memory region.
When PCC mode is enabled, the platform will not expose processor performance
or throttle states (_PSS, _TSS and related ACPI objects) to OSPM. Therefore,
the native P-state driver (such as acpi-cpufreq for Intel, powernow-k8 for
AMD) will not load.
However, OSPM remains in control of policy. The governor (eg: "ondemand")
computes the required performance for each processor based on server workload.
The PCC driver fills in the command interface, and the input buffer and
communicates the request to the platform firmware. The platform firmware is
responsible for delivering the requested performance.
Each PCC command is "global" in scope and can affect all the logical CPUs in
the system. Therefore, PCC is capable of performing "group" updates. With PCC
the OS is capable of getting/setting the frequency of all the logical CPUs in
the system with a single call to the BIOS.
1.1.1 Get Average Frequency:
----------------------------
This command is used by the OSPM to query the running frequency of the
processor since the last time this command was completed. The output buffer
indicates the average unhalted frequency of the logical processor expressed as
a percentage of the nominal (ie: maximum) CPU frequency. The output buffer
also signifies if the CPU frequency is limited by a power budget condition.
1.1.2 Set Desired Frequency:
----------------------------
This command is used by the OSPM to communicate to the platform firmware the
desired frequency for a logical processor. The output buffer is currently
ignored by OSPM. The next invocation of "Get Average Frequency" will inform
OSPM if the desired frequency was achieved or not.
1.2 Platforms affected:
-----------------------
The PCC driver will load on any system where the platform firmware:
* supports the PCC interface, and the associated PCCH() and PCCP() methods
* assumes responsibility for managing the hardware clocking controls in order
to deliver the requested processor performance
Currently, certain HP ProLiant platforms implement the PCC interface. On those
platforms PCC is the "default" choice.
However, it is possible to disable this interface via a BIOS setting. In
such an instance, as is also the case on platforms where the PCC interface
is not implemented, the PCC driver will fail to load silently.
2. Driver and /sys details:
---------------------------
When the driver loads, it merely prints the lowest and the highest CPU
frequencies supported by the platform firmware.
The PCC driver loads with a message such as:
pcc-cpufreq: (v1.00.00) driver loaded with frequency limits: 1600 MHz, 2933
MHz
This means that the OPSM can request the CPU to run at any frequency in
between the limits (1600 MHz, and 2933 MHz) specified in the message.
Internally, there is no need for the driver to convert the "target" frequency
to a corresponding P-state.
The VERSION number for the driver will be of the format v.xy.ab.
eg: 1.00.02
----- --
| |
| -- this will increase with bug fixes/enhancements to the driver
|-- this is the version of the PCC specification the driver adheres to
The following is a brief discussion on some of the fields exported via the
/sys filesystem and how their values are affected by the PCC driver:
2.1 scaling_available_frequencies:
----------------------------------
scaling_available_frequencies is not created in /sys. No intermediate
frequencies need to be listed because the BIOS will try to achieve any
frequency, within limits, requested by the governor. A frequency does not have
to be strictly associated with a P-state.
2.2 cpuinfo_transition_latency:
-------------------------------
The cpuinfo_transition_latency field is 0. The PCC specification does
not include a field to expose this value currently.
2.3 cpuinfo_cur_freq:
---------------------
A) Often cpuinfo_cur_freq will show a value different than what is declared
in the scaling_available_frequencies or scaling_cur_freq, or scaling_max_freq.
This is due to "turbo boost" available on recent Intel processors. If certain
conditions are met the BIOS can achieve a slightly higher speed than requested
by OSPM. An example:
scaling_cur_freq : 2933000
cpuinfo_cur_freq : 3196000
B) There is a round-off error associated with the cpuinfo_cur_freq value.
Since the driver obtains the current frequency as a "percentage" (%) of the
nominal frequency from the BIOS, sometimes, the values displayed by
scaling_cur_freq and cpuinfo_cur_freq may not match. An example:
scaling_cur_freq : 1600000
cpuinfo_cur_freq : 1583000
In this example, the nominal frequency is 2933 MHz. The driver obtains the
current frequency, cpuinfo_cur_freq, as 54% of the nominal frequency:
54% of 2933 MHz = 1583 MHz
Nominal frequency is the maximum frequency of the processor, and it usually
corresponds to the frequency of the P0 P-state.
2.4 related_cpus:
-----------------
The related_cpus field is identical to affected_cpus.
affected_cpus : 4
related_cpus : 4
Currently, the PCC driver does not evaluate _PSD. The platforms that support
PCC do not implement SW_ALL. So OSPM doesn't need to perform any coordination
to ensure that the same frequency is requested of all dependent CPUs.
3. Caveats:
-----------
The "cpufreq_stats" module in its present form cannot be loaded and
expected to work with the PCC driver. Since the "cpufreq_stats" module
provides information wrt each P-state, it is not applicable to the PCC driver.