Initial commit: Linux kernel 4.19 for Unplugged OS

This commit is contained in:
ziv committed 2025-10-06 13:52:42 +00:00
commit d30235b04c
80519 files changed
+35800681

No files matched your search

@@ -0,0 +1,71 @@
* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C)
Required properties:
- compatible : for SPI slave, use "adi,ad7879"
for I2C slave, use "adi,ad7879-1"
- reg : SPI chipselect/I2C slave address
See spi-bus.txt for more SPI slave properties
- interrupts : touch controller interrupt
- touchscreen-max-pressure : maximum reported pressure
- adi,resistance-plate-x : total resistance of X-plate (for pressure
calculation)
Optional properties:
- touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us)
13 : 2.560ms
14 : 3.584ms
15 : 4.096ms
This property has to be a '/bits/ 8' value
- adi,acquisition-time : 0: 2us
1: 4us
2: 8us
3: 16us
This property has to be a '/bits/ 8' value
- adi,median-filter-size : 0: disabled
1: 4 measurements
2: 8 measurements
3: 16 measurements
This property has to be a '/bits/ 8' value
- adi,averaging : 0: 2 middle values (1 if median disabled)
1: 4 middle values
2: 8 middle values
3: 16 values
This property has to be a '/bits/ 8' value
- adi,conversion-interval: : 0 : convert one time only
1-255: 515us + val * 35us (up to 9.440ms)
This property has to be a '/bits/ 8' value
- gpio-controller : Switch AUX/VBAT/GPIO pin to GPIO mode
Example:
ad7879@2c {
compatible = "adi,ad7879-1";
reg = <0x2c>;
interrupt-parent = <&gpio1>;
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
touchscreen-max-pressure = <4096>;
adi,resistance-plate-x = <120>;
adi,first-conversion-delay = /bits/ 8 <3>;
adi,acquisition-time = /bits/ 8 <1>;
adi,median-filter-size = /bits/ 8 <2>;
adi,averaging = /bits/ 8 <1>;
adi,conversion-interval = /bits/ 8 <255>;
};
ad7879@1 {
compatible = "adi,ad7879";
spi-max-frequency = <5000000>;
reg = <1>;
spi-cpol;
spi-cpha;
gpio-controller;
interrupt-parent = <&gpio1>;
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
touchscreen-max-pressure = <4096>;
adi,resistance-plate-x = <120>;
adi,first-conversion-delay = /bits/ 8 <3>;
adi,acquisition-time = /bits/ 8 <1>;
adi,median-filter-size = /bits/ 8 <2>;
adi,averaging = /bits/ 8 <1>;
adi,conversion-interval = /bits/ 8 <255>;
};
@@ -0,0 +1,93 @@
Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
SPI driven touch screen controllers.
The node for this driver must be a child node of a SPI controller, hence
all mandatory properties described in
Documentation/devicetree/bindings/spi/spi-bus.txt
must be specified.
Additional required properties:
compatible Must be one of the following, depending on the
model:
"ti,tsc2046"
"ti,ads7843"
"ti,ads7845"
"ti,ads7846"
"ti,ads7873"
interrupts An interrupt node describing the IRQ line the chip's
!PENIRQ pin is connected to.
vcc-supply A regulator node for the supply voltage.
Optional properties:
ti,vref-delay-usecs vref supply delay in usecs, 0 for
external vref (u16).
ti,vref-mv The VREF voltage, in millivolts (u16).
Set to 0 to use internal references
(ADS7846).
ti,keep-vref-on set to keep vref on for differential
measurements as well
ti,swap-xy swap x and y axis
ti,settle-delay-usec Settling time of the analog signals;
a function of Vcc and the capacitance
on the X/Y drivers. If set to non-zero,
two samples are taken with settle_delay
us apart, and the second one is used.
~150 uSec with 0.01uF caps (u16).
ti,penirq-recheck-delay-usecs If set to non-zero, after samples are
taken this delay is applied and penirq
is rechecked, to help avoid false
events. This value is affected by the
material used to build the touch layer
(u16).
ti,x-plate-ohms Resistance of the X-plate,
in Ohms (u16).
ti,y-plate-ohms Resistance of the Y-plate,
in Ohms (u16).
ti,x-min Minimum value on the X axis (u16).
ti,y-min Minimum value on the Y axis (u16).
ti,x-max Maximum value on the X axis (u16).
ti,y-max Minimum value on the Y axis (u16).
ti,pressure-min Minimum reported pressure value
(threshold) - u16.
ti,pressure-max Maximum reported pressure value (u16).
ti,debounce-max Max number of additional readings per
sample (u16).
ti,debounce-tol Tolerance used for filtering (u16).
ti,debounce-rep Additional consecutive good readings
required after the first two (u16).
ti,pendown-gpio-debounce Platform specific debounce time for the
pendown-gpio (u32).
pendown-gpio GPIO handle describing the pin the !PENIRQ
line is connected to.
wakeup-source use any event on touchscreen as wakeup event.
(Legacy property support: "linux,wakeup")
Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
spi_controller {
tsc2046@0 {
reg = <0>; /* CS0 */
compatible = "ti,tsc2046";
interrupt-parent = <&gpio1>;
interrupts = <8 0>; /* BOOT6 / GPIO 8 */
spi-max-frequency = <1000000>;
pendown-gpio = <&gpio1 8 0>;
vcc-supply = <&reg_vcc3>;
ti,x-min = /bits/ 16 <0>;
ti,x-max = /bits/ 16 <8000>;
ti,y-min = /bits/ 16 <0>;
ti,y-max = /bits/ 16 <4800>;
ti,x-plate-ohms = /bits/ 16 <40>;
ti,pressure-max = /bits/ 16 <255>;
wakeup-source;
};
};
@@ -0,0 +1,15 @@
* Microchip AR1020 and AR1021 touchscreen interface (I2C)
Required properties:
- compatible : "microchip,ar1021-i2c"
- reg : I2C slave address
- interrupts : touch controller interrupt
Example:
touchscreen@4d {
compatible = "microchip,ar1021-i2c";
reg = <0x4d>;
interrupt-parent = <&gpio3>;
interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
};
@@ -0,0 +1,30 @@
* AUO in-cell touchscreen controller using Pixcir sensors
Required properties:
- compatible: must be "auo,auo_pixcir_ts"
- reg: I2C address of the chip
- interrupts: interrupt to which the chip is connected
- gpios: gpios the chip is connected to
first one is the interrupt gpio and second one the reset gpio
- x-size: horizontal resolution of touchscreen
- y-size: vertical resolution of touchscreen
Example:
i2c@00000000 {
/* ... */
auo_pixcir_ts@5c {
compatible = "auo,auo_pixcir_ts";
reg = <0x5c>;
interrupts = <2 0>;
gpios = <&gpf 2 0 2>, /* INT */
<&gpf 5 1 0>; /* RST */
x-size = <800>;
y-size = <600>;
};
/* ... */
};
@@ -0,0 +1,87 @@
* Broadcom's IPROC Touchscreen Controller
Required properties:
- compatible: must be "brcm,iproc-touchscreen"
- ts_syscon: handler of syscon node defining physical base
address of the controller and length of memory mapped region.
If this property is selected please make sure MFD_SYSCON config
is enabled in the defconfig file.
- clocks: The clock provided by the SOC to driver the tsc
- clock-names: name for the clock
- interrupts: The touchscreen controller's interrupt
- address-cells: Specify the number of u32 entries needed in child nodes.
Should set to 1.
- size-cells: Specify number of u32 entries needed to specify child nodes size
in reg property. Should set to 1.
Optional properties:
- scanning_period: Time between scans. Each step is 1024 us. Valid 1-256.
- debounce_timeout: Each step is 512 us. Valid 0-255
- settling_timeout: The settling duration (in ms) is the amount of time
the tsc waits to allow the voltage to settle after
turning on the drivers in detection mode.
Valid values: 0-11
0 = 0.008 ms
1 = 0.01 ms
2 = 0.02 ms
3 = 0.04 ms
4 = 0.08 ms
5 = 0.16 ms
6 = 0.32 ms
7 = 0.64 ms
8 = 1.28 ms
9 = 2.56 ms
10 = 5.12 ms
11 = 10.24 ms
- touch_timeout: The continuous number of scan periods in which touch is
not detected before the controller returns to idle state.
Valid values 0-255.
- average_data: Number of data samples which are averaged before a final
data point is placed into the FIFO
Valid values 0-7
0 = 1 sample
1 = 2 samples
2 = 4 samples
3 = 8 samples
4 = 16 samples
5 = 32 samples
6 = 64 samples
7 = 128 samples
- fifo_threshold: Interrupt is generated whenever the number of fifo
entries exceeds this value
Valid values 0-31
- touchscreen-size-x: horizontal resolution of touchscreen (in pixels)
- touchscreen-size-y: vertical resolution of touchscreen (in pixels)
- touchscreen-fuzz-x: horizontal noise value of the absolute input
device (in pixels)
- touchscreen-fuzz-y: vertical noise value of the absolute input
device (in pixels)
- touchscreen-inverted-x: X axis is inverted (boolean)
- touchscreen-inverted-y: Y axis is inverted (boolean)
Example: An example of touchscreen node
ts_adc_syscon: ts_adc_syscon@180a6000 {
compatible = "brcm,iproc-ts-adc-syscon","syscon";
reg = <0x180a6000 0xc30>;
};
touchscreen: touchscreen@180a6000 {
compatible = "brcm,iproc-touchscreen";
#address-cells = <1>;
#size-cells = <1>;
ts_syscon = <&ts_adc_syscon>;
clocks = <&adc_clk>;
clock-names = "tsc_clk";
interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
scanning_period = <5>;
debounce_timeout = <40>;
settling_timeout = <7>;
touch_timeout = <10>;
average_data = <5>;
fifo_threshold = <1>;
/* Touchscreen is rotated 180 degrees. */
touchscreen-inverted-x;
touchscreen-inverted-y;
};
@@ -0,0 +1,28 @@
* Rohm BU21013 Touch Screen
Required properties:
- compatible : "rohm,bu21013_tp"
- reg : I2C device address
Optional properties:
- touch-gpio : GPIO pin registering a touch event
- <supply_name>-supply : Phandle to a regulator supply
- rohm,touch-max-x : Maximum outward permitted limit in the X axis
- rohm,touch-max-y : Maximum outward permitted limit in the Y axis
- rohm,flip-x : Flip touch coordinates on the X axis
- rohm,flip-y : Flip touch coordinates on the Y axis
Example:
i2c@80110000 {
bu21013_tp@5c {
compatible = "rohm,bu21013_tp";
reg = <0x5c>;
touch-gpio = <&gpio2 20 0x4>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
rohm,touch-max-y = <704>;
rohm,flip-y;
};
};
@@ -0,0 +1,35 @@
* Rohm BU21029 Touch Screen Controller
Required properties:
- compatible : must be "rohm,bu21029"
- reg : i2c device address of the chip (0x40 or 0x41)
- interrupt-parent : the phandle for the gpio controller
- interrupts : (gpio) interrupt to which the chip is connected
- rohm,x-plate-ohms : x-plate resistance in Ohm
Optional properties:
- reset-gpios : gpio pin to reset the chip (active low)
- touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
- touchscreen-size-y : vertical resolution of touchscreen (in pixels)
- touchscreen-max-pressure: maximum pressure value
- vdd-supply : power supply for the controller
Example:
&i2c1 {
/* ... */
bu21029: bu21029@40 {
compatible = "rohm,bu21029";
reg = <0x40>;
interrupt-parent = <&gpio1>;
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
reset-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;
rohm,x-plate-ohms = <600>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-max-pressure = <4095>;
};
/* ... */
};
@@ -0,0 +1,44 @@
* ChipOne icn8318 I2C touchscreen controller
Required properties:
- compatible : "chipone,icn8318"
- reg : I2C slave address of the chip (0x40)
- interrupts : interrupt specification for the icn8318 interrupt
- wake-gpios : GPIO specification for the WAKE input
- touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
- touchscreen-size-y : vertical resolution of touchscreen (in pixels)
Optional properties:
- pinctrl-names : should be "default"
- pinctrl-0: : a phandle pointing to the pin settings for the
control gpios
- touchscreen-fuzz-x : horizontal noise value of the absolute input
device (in pixels)
- touchscreen-fuzz-y : vertical noise value of the absolute input
device (in pixels)
- touchscreen-inverted-x : X axis is inverted (boolean)
- touchscreen-inverted-y : Y axis is inverted (boolean)
- touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
Swapping is done after inverting the axis
Example:
i2c@00000000 {
/* ... */
chipone_icn8318@40 {
compatible = "chipone,icn8318";
reg = <0x40>;
interrupt-parent = <&pio>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
pinctrl-names = "default";
pinctrl-0 = <&ts_wake_pin_p66>;
wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-swapped-x-y;
};
/* ... */
};
@@ -0,0 +1,34 @@
* Toradex Colibri VF50 Touchscreen driver
Required Properties:
- compatible must be toradex,vf50-touchscreen
- io-channels: adc channels being used by the Colibri VF50 module
- xp-gpios: FET gate driver for input of X+
- xm-gpios: FET gate driver for input of X-
- yp-gpios: FET gate driver for input of Y+
- ym-gpios: FET gate driver for input of Y-
- interrupts: pen irq interrupt for touch detection
- pinctrl-names: "idle", "default", "gpios"
- pinctrl-0: pinctrl node for pen/touch detection state pinmux
- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux
- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers
- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
Example:
touchctrl: vf50_touchctrl {
compatible = "toradex,vf50-touchscreen";
io-channels = <&adc1 0>,<&adc0 0>,
<&adc0 1>,<&adc1 2>;
xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
interrupt-parent = <&gpio0>;
interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "idle","default","gpios";
pinctrl-0 = <&pinctrl_touchctrl_idle>;
pinctrl-1 = <&pinctrl_touchctrl_default>;
pinctrl-2 = <&pinctrl_touchctrl_gpios>;
vf50-ts-min-pressure = <200>;
};
@@ -0,0 +1,93 @@
* Cypress cyttsp touchscreen controller
Required properties:
- compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi"
- reg : Device I2C address or SPI chip select number
- spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi)
- interrupts : (gpio) interrupt to which the chip is connected
(see interrupt binding[0]).
- bootloader-key : the 8-byte bootloader key that is required to switch
the chip from bootloader mode (default mode) to
application mode.
This property has to be specified as an array of 8
'/bits/ 8' values.
Optional properties:
- reset-gpios : the reset gpio the chip is connected to
(see GPIO binding[1] for more details).
- touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
- touchscreen-size-y : vertical resolution of touchscreen (in pixels)
- touchscreen-fuzz-x : horizontal noise value of the absolute input device
(in pixels)
- touchscreen-fuzz-y : vertical noise value of the absolute input device
(in pixels)
- active-distance : the distance in pixels beyond which a touch must move
before movement is detected and reported by the device.
Valid values: 0-15.
- active-interval-ms : the minimum period in ms between consecutive
scanning/processing cycles when the chip is in active mode.
Valid values: 0-255.
- lowpower-interval-ms : the minimum period in ms between consecutive
scanning/processing cycles when the chip is in low-power mode.
Valid values: 0-2550
- touch-timeout-ms : minimum time in ms spent in the active power state while no
touches are detected before entering low-power mode.
Valid values: 0-2550
- use-handshake : enable register-based handshake (boolean). This should
only be used if the chip is configured to use 'blocking
communication with timeout' (in this case the device
generates an interrupt at the end of every
scanning/processing cycle).
[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
[1]: Documentation/devicetree/bindings/gpio/gpio.txt
Example:
&i2c1 {
/* ... */
cyttsp@a {
compatible = "cypress,cyttsp-i2c";
reg = <0xa>;
interrupt-parent = <&gpio0>;
interrupts = <28 0>;
reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-fuzz-x = <4>;
touchscreen-fuzz-y = <7>;
bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
active-distance = <8>;
active-interval-ms = <0>;
lowpower-interval-ms = <200>;
touch-timeout-ms = <100>;
};
/* ... */
};
&mcspi1 {
/* ... */
cyttsp@0 {
compatible = "cypress,cyttsp-spi";
spi-max-frequency = <6000000>;
reg = <0>;
interrupt-parent = <&gpio0>;
interrupts = <28 0>;
reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-fuzz-x = <4>;
touchscreen-fuzz-y = <7>;
bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
active-distance = <8>;
active-interval-ms = <0>;
lowpower-interval-ms = <200>;
touch-timeout-ms = <100>;
};
/* ... */
};
@@ -0,0 +1,63 @@
FocalTech EDT-FT5x06 Polytouch driver
=====================================
There are 3 variants of the chip for various touch panel sizes
FT5206GE1 2.8" .. 3.8"
FT5306DE4 4.3" .. 7"
FT5406EE8 7" .. 8.9"
FT5506EEG 7" .. 8.9"
The software interface is identical for all those chips, so that
currently there is no need for the driver to distinguish between the
different chips. Nevertheless distinct compatible strings are used so
that a distinction can be added if necessary without changing the DT
bindings.
Required properties:
- compatible: "edt,edt-ft5206"
or: "edt,edt-ft5306"
or: "edt,edt-ft5406"
or: "edt,edt-ft5506"
or: "focaltech,ft6236"
- reg: I2C slave address of the chip (0x38)
- interrupts: interrupt specification for the touchdetect
interrupt
Optional properties:
- reset-gpios: GPIO specification for the RESET input
- wake-gpios: GPIO specification for the WAKE input
- pinctrl-names: should be "default"
- pinctrl-0: a phandle pointing to the pin settings for the
control gpios
- threshold: allows setting the "click"-threshold in the range
from 0 to 80.
- gain: allows setting the sensitivity in the range from 0 to
31. Note that lower values indicate higher
sensitivity.
- offset: allows setting the edge compensation in the range from
0 to 31.
- touchscreen-size-x : See touchscreen.txt
- touchscreen-size-y : See touchscreen.txt
- touchscreen-fuzz-x : See touchscreen.txt
- touchscreen-fuzz-y : See touchscreen.txt
- touchscreen-inverted-x : See touchscreen.txt
- touchscreen-inverted-y : See touchscreen.txt
- touchscreen-swapped-x-y : See touchscreen.txt
Example:
polytouch: edt-ft5x06@38 {
compatible = "edt,edt-ft5406", "edt,edt-ft5x06";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&edt_ft5x06_pins>;
interrupt-parent = <&gpio2>;
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
};
@@ -0,0 +1,30 @@
Bindings for EETI touchscreen controller
Required properties:
- compatible: should be "eeti,exc3000-i2c"
- reg: I2C address of the chip. Should be set to <0xa>
- interrupts: interrupt to which the chip is connected
Optional properties:
- attn-gpios: A handle to a GPIO to check whether interrupt is still
latched. This is necessary for platforms that lack
support for level-triggered IRQs.
The following optional properties described in touchscreen.txt are
also supported:
- touchscreen-inverted-x
- touchscreen-inverted-y
- touchscreen-swapped-x-y
Example:
i2c-master {
touchscreen@a {
compatible = "eeti,exc3000-i2c";
reg = <0xa>;
interrupt-parent = <&gpio>;
interrupts = <123 IRQ_TYPE_EDGE_RISING>;
attn-gpios = <&gpio 123 GPIO_ACTIVE_HIGH>;
};
};
@@ -0,0 +1,18 @@
* EETI eGalax Multiple Touch Controller
Required properties:
- compatible: must be "eeti,egalax_ts"
- reg: i2c slave address
- interrupts: touch controller interrupt
- wakeup-gpios: the gpio pin to be used for waking up the controller
and also used as irq pin
Example:
touchscreen@4 {
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio1>;
interrupts = <9 2>;
wakeup-gpios = <&gpio1 9 0>;
};
@@ -0,0 +1,25 @@
* Elan eKTF2127 I2C touchscreen controller
Required properties:
- compatible : "elan,ektf2127"
- reg : I2C slave address of the chip (0x40)
- interrupts : interrupt specification for the ektf2127 interrupt
- power-gpios : GPIO specification for the pin connected to the
ektf2127's wake input. This needs to be driven high
to take ektf2127 out of it's low power state
For additional optional properties see: touchscreen.txt
Example:
i2c@00000000 {
ektf2127: touchscreen@15 {
compatible = "elan,ektf2127";
reg = <0x15>;
interrupt-parent = <&pio>;
interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>
power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>;
touchscreen-inverted-x;
touchscreen-swapped-x-y;
};
};
@@ -0,0 +1,26 @@
* EETI EXC3000 Multiple Touch Controller
Required properties:
- compatible: must be "eeti,exc3000"
- reg: i2c slave address
- interrupts: touch controller interrupt
- touchscreen-size-x: See touchscreen.txt
- touchscreen-size-y: See touchscreen.txt
Optional properties:
- touchscreen-inverted-x: See touchscreen.txt
- touchscreen-inverted-y: See touchscreen.txt
- touchscreen-swapped-x-y: See touchscreen.txt
Example:
touchscreen@2a {
compatible = "eeti,exc3000";
reg = <0x2a>;
interrupt-parent = <&gpio1>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
touchscreen-size-x = <4096>;
touchscreen-size-y = <4096>;
touchscreen-inverted-x;
touchscreen-swapped-x-y;
};
@@ -0,0 +1,34 @@
Freescale mx25 TS conversion queue module
mx25 touchscreen conversion queue module which controls the ADC unit of the
mx25 for attached touchscreens.
Required properties:
- compatible: Should be "fsl,imx25-tcq".
- reg: Memory range of the device.
- interrupts: Should be the interrupt number associated with this module within
the tscadc unit (<0>).
- fsl,wires: Should be '<4>' or '<5>'
Optional properties:
- fsl,pen-debounce-ns: Pen debounce time in nanoseconds.
- fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value
between 1 and 4096. It is the ratio between the internal reference voltage
and the measured voltage after the plate was precharged. Resistance between
plates and therefore the voltage decreases with pressure so that a smaller
value is equivalent to a higher pressure.
- fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before
the actual touch detection to wait for an even charge distribution in the
plate.
This device includes two conversion queues which can be added as subnodes.
The first queue is for the touchscreen, the second for general purpose ADC.
Example:
tsc: tcq@50030400 {
compatible = "fsl,imx25-tcq";
reg = <0x50030400 0x60>;
interrupt-parent = <&tscadc>;
interrupts = <0>;
fsl,wires = <4>;
};
@@ -0,0 +1,43 @@
Device tree bindings for Goodix GT9xx series touchscreen controller
Required properties:
- compatible : Should be "goodix,gt1151"
or "goodix,gt911"
or "goodix,gt9110"
or "goodix,gt912"
or "goodix,gt927"
or "goodix,gt9271"
or "goodix,gt928"
or "goodix,gt967"
- reg : I2C address of the chip. Should be 0x5d or 0x14
- interrupts : Interrupt to which the chip is connected
Optional properties:
- irq-gpios : GPIO pin used for IRQ. The driver uses the
interrupt gpio pin as output to reset the device.
- reset-gpios : GPIO pin used for reset
- touchscreen-inverted-x : X axis is inverted (boolean)
- touchscreen-inverted-y : Y axis is inverted (boolean)
- touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
(swapping is done after inverting the axis)
Example:
i2c@00000000 {
/* ... */
gt928@5d {
compatible = "goodix,gt928";
reg = <0x5d>;
interrupt-parent = <&gpio>;
interrupts = <0 0>;
irq-gpios = <&gpio1 0 0>;
reset-gpios = <&gpio1 1 0>;
};
/* ... */
};
@@ -0,0 +1,41 @@
* HiDeep Finger and Stylus touchscreen controller
Required properties:
- compatible : must be "hideep,hideep-ts"
- reg : I2C slave address, (e.g. 0x6C).
- interrupts : Interrupt to which the chip is connected.
Optional properties:
- vdd-supply : It is the controller supply for controlling
main voltage(3.3V) through the regulator.
- vid-supply : It is the controller supply for controlling
IO voltage(1.8V) through the regulator.
- reset-gpios : Define for reset gpio pin.
It is to use for reset IC.
- touchscreen-size-x : X axis size of touchscreen
- touchscreen-size-y : Y axis size of touchscreen
- linux,keycodes : Specifies an array of numeric keycode values to
be used for reporting button presses. The array can
contain up to 3 entries.
Example:
#include "dt-bindings/input/input.h"
i2c@00000000 {
/* ... */
touchscreen@6c {
compatible = "hideep,hideep-ts";
reg = <0x6c>;
interrupt-parent = <&gpx1>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
vdd-supply = <&ldo15_reg>;
vid-supply = <&ldo18_reg>;
reset-gpios = <&gpx1 5 0>;
touchscreen-size-x = <1080>;
touchscreen-size-y = <1920>;
linux,keycodes = <KEY_HOME>, <KEY_MENU>, <KEY_BACK>;
};
};
@@ -0,0 +1,38 @@
* Freescale i.MX6UL Touch Controller
Required properties:
- compatible: must be "fsl,imx6ul-tsc".
- reg: this touch controller address and the ADC2 address.
- interrupts: the interrupt of this touch controller and ADC2.
- clocks: the root clock of touch controller and ADC2.
- clock-names; must be "tsc" and "adc".
- xnur-gpio: the X- gpio this controller connect to.
This xnur-gpio returns to low once the finger leave the touch screen (The
last touch event the touch controller capture).
Optional properties:
- measure-delay-time: the value of measure delay time.
Before X-axis or Y-axis measurement, the screen need some time before
even potential distribution ready.
This value depends on the touch screen.
- pre-charge-time: the touch screen need some time to precharge.
This value depends on the touch screen.
- touchscreen-average-samples: Number of data samples which are averaged for
each read. Valid values are 1, 4, 8, 16 and 32.
Example:
tsc: tsc@2040000 {
compatible = "fsl,imx6ul-tsc";
reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6UL_CLK_IPG>,
<&clks IMX6UL_CLK_ADC2>;
clock-names = "tsc", "adc";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
measure-delay-time = <0xfff>;
pre-charge-time = <0xffff>;
touchscreen-average-samples = <32>;
};
@@ -0,0 +1,16 @@
* NXP LPC32xx SoC Touchscreen Controller (TSC)
Required properties:
- compatible: must be "nxp,lpc3220-tsc"
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: The TSC/ADC interrupt
Example:
tsc@40048000 {
compatible = "nxp,lpc3220-tsc";
reg = <0x40048000 0x1000>;
interrupt-parent = <&mic>;
interrupts = <39 0>;
};
@@ -0,0 +1,17 @@
* MAXI MAX11801 Resistive touch screen controller with i2c interface
Required properties:
- compatible: must be "maxim,max11801"
- reg: i2c slave address
- interrupts: touch controller interrupt
Example:
&i2c1 {
max11801: touchscreen@48 {
compatible = "maxim,max11801";
reg = <0x48>;
interrupt-parent = <&gpio3>;
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
};
};
@@ -0,0 +1,20 @@
* MELFAS MIP4 Touchscreen
Required properties:
- compatible: must be "melfas,mip4_ts"
- reg: I2C slave address of the chip (0x48 or 0x34)
- interrupts: interrupt to which the chip is connected
Optional properties:
- ce-gpios: GPIO connected to the CE (chip enable) pin of the chip
Example:
i2c@00000000 {
touchscreen: melfas_mip4@48 {
compatible = "melfas,mip4_ts";
reg = <0x48>;
interrupt-parent = <&gpio>;
interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
ce-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
};
};
@@ -0,0 +1,41 @@
* MELFAS MMS114/MMS152 touchscreen controller
Required properties:
- compatible: should be one of:
- "melfas,mms114"
- "melfas,mms152"
- reg: I2C address of the chip
- interrupts: interrupt to which the chip is connected
- touchscreen-size-x: See [1]
- touchscreen-size-y: See [1]
Optional properties:
- touchscreen-fuzz-x: See [1]
- touchscreen-fuzz-y: See [1]
- touchscreen-fuzz-pressure: See [1]
- touchscreen-inverted-x: See [1]
- touchscreen-inverted-y: See [1]
- touchscreen-swapped-x-y: See [1]
[1]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
Example:
i2c@00000000 {
/* ... */
touchscreen@48 {
compatible = "melfas,mms114";
reg = <0x48>;
interrupts = <39 0>;
touchscreen-size-x = <720>;
touchscreen-size-y = <1280>;
touchscreen-fuzz-x = <10>;
touchscreen-fuzz-y = <10>;
touchscreen-fuzz-pressure = <10>;
touchscreen-inverted-x;
touchscreen-inverted-y;
};
/* ... */
};
@@ -0,0 +1,31 @@
* Pixcir I2C touchscreen controllers
Required properties:
- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc"
- reg: I2C address of the chip
- interrupts: interrupt to which the chip is connected
- attb-gpio: GPIO connected to the ATTB line of the chip
- touchscreen-size-x: horizontal resolution of touchscreen (in pixels)
- touchscreen-size-y: vertical resolution of touchscreen (in pixels)
Optional properties:
- reset-gpios: GPIO connected to the RESET line of the chip
- enable-gpios: GPIO connected to the ENABLE line of the chip
- wake-gpios: GPIO connected to the WAKE line of the chip
Example:
i2c@00000000 {
/* ... */
pixcir_ts@5c {
compatible = "pixcir,pixcir_ts";
reg = <0x5c>;
interrupts = <2 0>;
attb-gpio = <&gpf 2 0 2>;
touchscreen-size-x = <800>;
touchscreen-size-y = <600>;
};
/* ... */
};
@@ -0,0 +1,30 @@
Generic resistive touchscreen ADC
Required properties:
- compatible: must be "resistive-adc-touch"
The device must be connected to an ADC device that provides channels for
position measurement and optional pressure.
Refer to ../iio/iio-bindings.txt for details
- iio-channels: must have at least two channels connected to an ADC device.
These should correspond to the channels exposed by the ADC device and should
have the right index as the ADC device registers them. These channels
represent the relative position on the "x" and "y" axes.
- iio-channel-names: must have all the channels' names. Mandatory channels
are "x" and "y".
Optional properties:
- iio-channels: The third channel named "pressure" is optional and can be
used if the ADC device also measures pressure besides position.
If this channel is missing, pressure will be ignored and the touchscreen
will only report position.
- iio-channel-names: optional channel named "pressure".
Example:
resistive_touch: resistive_touch {
compatible = "resistive-adc-touch";
touchscreen-min-pressure = <50000>;
io-channels = <&adc 24>, <&adc 25>, <&adc 26>;
io-channel-names = "x", "y", "pressure";
};
@@ -0,0 +1,32 @@
* Samsung S6SY761 touchscreen controller
Required properties:
- compatible : must be "samsung,s6sy761"
- reg : I2C slave address, (e.g. 0x48)
- interrupts : interrupt specification
- avdd-supply : analogic power supply
- vdd-supply : power supply
Optional properties:
- touchscreen-size-x : see touchscreen.txt. This property is embedded in the
device. If defined it forces a different x resolution.
- touchscreen-size-y : see touchscreen.txt. This property is embedded in the
device. If defined it forces a different y resolution.
Example:
i2c@00000000 {
/* ... */
touchscreen@48 {
compatible = "samsung,s6sy761";
reg = <0x48>;
interrupt-parent = <&gpa1>;
interrupts = <1 IRQ_TYPE_NONE>;
avdd-supply = <&ldo30_reg>;
vdd-supply = <&ldo31_reg>;
touchscreen-size-x = <4096>;
touchscreen-size-y = <4096>;
};
};
@@ -0,0 +1,44 @@
* GSL 1680 touchscreen controller
Required properties:
- compatible : Must be one of the following, depending on the model:
"silead,gsl1680"
"silead,gsl1688"
"silead,gsl3670"
"silead,gsl3675"
"silead,gsl3692"
- reg : I2C slave address of the chip (0x40)
- interrupts : interrupt specification for the gsl1680 interrupt
- power-gpios : Specification for the pin connected to the gsl1680's
shutdown input. This needs to be driven high to take the
gsl1680 out of its low power state
- touchscreen-size-x : See touchscreen.txt
- touchscreen-size-y : See touchscreen.txt
Optional properties:
- firmware-name : File basename (string) for board specific firmware
- touchscreen-inverted-x : See touchscreen.txt
- touchscreen-inverted-y : See touchscreen.txt
- touchscreen-swapped-x-y : See touchscreen.txt
- silead,max-fingers : maximum number of fingers the touchscreen can detect
- silead,home-button : Boolean, set to true on devices which have a
capacitive home-button build into the touchscreen
- vddio-supply : regulator phandle for controller VDDIO
- avdd-supply : regulator phandle for controller AVDD
Example:
i2c@00000000 {
gsl1680: touchscreen@40 {
compatible = "silead,gsl1680";
reg = <0x40>;
interrupt-parent = <&pio>;
interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>;
power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>;
touchscreen-size-x = <480>;
touchscreen-size-y = <800>;
touchscreen-inverted-x;
touchscreen-swapped-x-y;
silead,max-fingers = <5>;
};
};
@@ -0,0 +1,31 @@
* SiS I2C Multiple Touch Controller
Required properties:
- compatible: must be "sis,9200-ts"
- reg: i2c slave address
- interrupts: touch controller interrupt (see interrupt
binding [0])
Optional properties:
- pinctrl-names: should be "default" (see pinctrl binding [1]).
- pinctrl-0: a phandle pointing to the pin settings for the
device (see pinctrl binding [1]).
- attn-gpios: the gpio pin used as attention line
- reset-gpios: the gpio pin used to reset the controller
- wakeup-source: touchscreen can be used as a wakeup source
[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
Example:
sis9255@5c {
compatible = "sis,9200-ts";
reg = <0x5c>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sis>;
interrupt-parent = <&gpio3>;
interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
};
@@ -0,0 +1,24 @@
* Sitronix st1232 touchscreen controller
Required properties:
- compatible: must be "sitronix,st1232"
- reg: I2C address of the chip
- interrupts: interrupt to which the chip is connected
Optional properties:
- gpios: a phandle to the reset GPIO
Example:
i2c@00000000 {
/* ... */
touchscreen@55 {
compatible = "sitronix,st1232";
reg = <0x55>;
interrupts = <2 0>;
gpios = <&gpio1 166 0>;
};
/* ... */
};
@@ -0,0 +1,41 @@
* ST-Microelectronics FingerTip touchscreen controller
The ST-Microelectronics FingerTip device provides a basic touchscreen
functionality. Along with it the user can enable the touchkey which can work as
a basic HOME and BACK key for phones.
The driver supports also hovering as an absolute single touch event with x, y, z
coordinates.
Required properties:
- compatible : must be "st,stmfts"
- reg : I2C slave address, (e.g. 0x49)
- interrupts : interrupt specification
- avdd-supply : analogic power supply
- vdd-supply : power supply
- touchscreen-size-x : see touchscreen.txt
- touchscreen-size-y : see touchscreen.txt
Optional properties:
- touch-key-connected : specifies whether the touchkey feature is connected
- ledvdd-supply : power supply to the touch key leds
Example:
i2c@00000000 {
/* ... */
touchscreen@49 {
compatible = "st,stmfts";
reg = <0x49>;
interrupt-parent = <&gpa1>;
interrupts = <1 IRQ_TYPE_NONE>;
touchscreen-size-x = <1599>;
touchscreen-size-y = <2559>;
touch-key-connected;
avdd-supply = <&ldo30_reg>;
vdd-supply = <&ldo31_reg>;
ledvdd-supply = <&ldo33_reg>;
};
};
@@ -0,0 +1,43 @@
STMPE Touchscreen
----------------
Required properties:
- compatible: "st,stmpe-ts"
Optional properties:
- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 ->
44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6
-> 144 clocks), recommended is 4.
- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external
reference)
- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4
samples, 3 -> 8 samples)
- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 ->
100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended
is 3
- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3
-> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2
- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of
the fractional part) recommended is 7
- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35
mA max, 1 -> 50 mA typical 80 mA max)
Node name must be stmpe_touchscreen and should be child node of stmpe node to
which it belongs.
Example:
stmpe_touchscreen {
compatible = "st,stmpe-ts";
st,sample-time = <4>;
st,mod-12b = <1>;
st,ref-sel = <0>;
st,adc-freq = <1>;
st,ave-ctrl = <1>;
st,touch-det-delay = <2>;
st,settling = <2>;
st,fraction-z = <7>;
st,i-drive = <1>;
};
@@ -0,0 +1,15 @@
* Semtech SX8654 I2C Touchscreen Controller
Required properties:
- compatible: must be "semtech,sx8654"
- reg: i2c slave address
- interrupts: touch controller interrupt
Example:
sx8654@48 {
compatible = "semtech,sx8654";
reg = <0x48>;
interrupt-parent = <&gpio6>;
interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
};
@@ -0,0 +1,83 @@
* TI - TSC ADC (Touschscreen and analog digital converter)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Required properties:
- child "tsc"
ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
support on the platform.
ti,x-plate-resistance: X plate resistance
ti,coordinate-readouts: The sequencer supports a total of 16
programmable steps each step is used to
read a single coordinate. A single
readout is enough but multiple reads can
increase the quality.
A value of 5 means, 5 reads for X, 5 for
Y and 2 for Z (always). This utilises 12
of the 16 software steps available. The
remaining 4 can be used by the ADC.
ti,wire-config: Different boards could have a different order for
connecting wires on touchscreen. We need to provide an
8 bit number where in the 1st four bits represent the
analog lines and the next 4 bits represent positive/
negative terminal on that input line. Notations to
represent the input lines and terminals resoectively
is as follows:
AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
XP = 0, XN = 1, YP = 2, YN = 3.
- child "adc"
ti,adc-channels: List of analog inputs available for ADC.
AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
Optional properties:
- child "tsc"
ti,charge-delay: Length of touch screen charge delay step in terms of
ADC clock cycles. Charge delay value should be large
in order to avoid false pen-up events. This value
effects the overall sampling speed, hence need to be
kept as low as possible, while avoiding false pen-up
event. Start from a lower value, say 0x400, and
increase value until false pen-up events are avoided.
The pen-up detection happens immediately after the
charge step, so this does in fact function as a
hardware knob for adjusting the amount of "settling
time".
- child "adc"
ti,chan-step-opendelay: List of open delays for each channel of
ADC in the order of ti,adc-channels. The
value corresponds to the number of ADC
clock cycles to wait after applying the
step configuration registers and before
sending the start of ADC conversion.
Maximum value is 0x3FFFF.
ti,chan-step-sampledelay: List of sample delays for each channel
of ADC in the order of ti,adc-channels.
The value corresponds to the number of
ADC clock cycles to sample (to hold
start of conversion high).
Maximum value is 0xFF.
ti,chan-step-avg: Number of averages to be performed for each
channel of ADC. If average is 16 then input
is sampled 16 times and averaged to get more
accurate value. This increases the time taken
by ADC to generate a sample. Valid range is 0
average to 16 averages. Maximum value is 16.
Example:
tscadc: tscadc@44e0d000 {
compatible = "ti,am3359-tscadc";
tsc {
ti,wires = <4>;
ti,x-plate-resistance = <200>;
ti,coordiante-readouts = <5>;
ti,wire-config = <0x00 0x11 0x22 0x33>;
ti,charge-delay = <0x400>;
};
adc {
ti,adc-channels = <4 5 6 7>;
ti,chan-step-opendelay = <0x098 0x3ffff 0x098 0x0>;
ti,chan-step-sampledelay = <0xff 0x0 0xf 0x0>;
ti,chan-step-avg = <16 2 4 8>;
};
}
@@ -0,0 +1,37 @@
General Touchscreen Properties:
Optional properties for Touchscreens:
- touchscreen-size-x : horizontal resolution of touchscreen
(in pixels)
- touchscreen-size-y : vertical resolution of touchscreen
(in pixels)
- touchscreen-max-pressure : maximum reported pressure (arbitrary range
dependent on the controller)
- touchscreen-min-pressure : minimum pressure on the touchscreen to be
achieved in order for the touchscreen
driver to report a touch event.
- touchscreen-fuzz-x : horizontal noise value of the absolute input
device (in pixels)
- touchscreen-fuzz-y : vertical noise value of the absolute input
device (in pixels)
- touchscreen-fuzz-pressure : pressure noise value of the absolute input
device (arbitrary range dependent on the
controller)
- touchscreen-average-samples : Number of data samples which are averaged
for each read (valid values dependent on the
controller)
- touchscreen-inverted-x : X axis is inverted (boolean)
- touchscreen-inverted-y : Y axis is inverted (boolean)
- touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
Swapping is done after inverting the axis
- touchscreen-x-mm : horizontal length in mm of the touchscreen
- touchscreen-y-mm : vertical length in mm of the touchscreen
Deprecated properties for Touchscreens:
- x-size : deprecated name for touchscreen-size-x
- y-size : deprecated name for touchscreen-size-y
- moving-threshold : deprecated name for a combination of
touchscreen-fuzz-x and touchscreen-fuzz-y
- contact-threshold : deprecated name for touchscreen-fuzz-pressure
- x-invert : deprecated name for touchscreen-inverted-x
- y-invert : deprecated name for touchscreen-inverted-y
@@ -0,0 +1,11 @@
* TS-4800 Touchscreen bindings
Required properties:
- compatible: must be "technologic,ts4800-ts"
- reg: physical base address of the controller and length of memory mapped
region.
- syscon: phandle / integers array that points to the syscon node which
describes the FPGA's syscon registers.
- phandle to FPGA's syscon
- offset to the touchscreen register
- offset to the touchscreen enable bit
@@ -0,0 +1,64 @@
* Texas Instruments tsc2004 and tsc2005 touchscreen controllers
Required properties:
- compatible : "ti,tsc2004" or "ti,tsc2005"
- reg : Device address
- interrupts : IRQ specifier
- spi-max-frequency : Maximum SPI clocking speed of the device
(for tsc2005)
Optional properties:
- vio-supply : Regulator specifier
- reset-gpios : GPIO specifier for the controller reset line
- ti,x-plate-ohms : integer, resistance of the touchscreen's X plates
in ohm (defaults to 280)
- ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after
the configured time (in milli seconds), the driver
will reset it. This is disabled by default.
- properties defined in touchscreen.txt
Example:
&i2c3 {
tsc2004@48 {
compatible = "ti,tsc2004";
reg = <0x48>;
vio-supply = <&vio>;
reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>;
touchscreen-fuzz-x = <4>;
touchscreen-fuzz-y = <7>;
touchscreen-fuzz-pressure = <2>;
touchscreen-size-x = <4096>;
touchscreen-size-y = <4096>;
touchscreen-max-pressure = <2048>;
ti,x-plate-ohms = <280>;
ti,esd-recovery-timeout-ms = <8000>;
};
}
&mcspi1 {
tsc2005@0 {
compatible = "ti,tsc2005";
spi-max-frequency = <6000000>;
reg = <0>;
vio-supply = <&vio>;
reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
touchscreen-fuzz-x = <4>;
touchscreen-fuzz-y = <7>;
touchscreen-fuzz-pressure = <2>;
touchscreen-size-x = <4096>;
touchscreen-size-y = <4096>;
touchscreen-max-pressure = <2048>;
ti,x-plate-ohms = <280>;
ti,esd-recovery-timeout-ms = <8000>;
};
}
@@ -0,0 +1,39 @@
* Texas Instruments tsc2007 touchscreen controller
Required properties:
- compatible: must be "ti,tsc2007".
- reg: I2C address of the chip.
- ti,x-plate-ohms: X-plate resistance in ohms.
Optional properties:
- gpios: the interrupt gpio the chip is connected to (trough the penirq pin).
The penirq pin goes to low when the panel is touched.
(see GPIO binding[1] for more details).
- interrupts: (gpio) interrupt to which the chip is connected
(see interrupt binding[0]).
- ti,max-rt: maximum pressure.
- ti,fuzzx: specifies the absolute input fuzz x value.
If set, it will permit noise in the data up to +- the value given to the fuzz
parameter, that is used to filter noise from the event stream.
- ti,fuzzy: specifies the absolute input fuzz y value.
- ti,fuzzz: specifies the absolute input fuzz z value.
- ti,poll-period: how much time to wait (in milliseconds) before reading again the
values from the tsc2007.
[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
[1]: Documentation/devicetree/bindings/gpio/gpio.txt
Example:
&i2c1 {
/* ... */
tsc2007@49 {
compatible = "ti,tsc2007";
reg = <0x49>;
interrupt-parent = <&gpio4>;
interrupts = <0x0 0x8>;
gpios = <&gpio4 0 0>;
ti,x-plate-ohms = <180>;
};
/* ... */
};
@@ -0,0 +1,30 @@
Zeitec ZET6223 I2C touchscreen controller
Required properties:
- compatible : "zeitec,zet6223"
- reg : I2C slave address of the chip (0x76)
- interrupts : interrupt specification for the zet6223 interrupt
Optional properties:
- vio-supply : Specification for VIO supply (1.8V or 3.3V,
depending on system interface needs).
- vcc-supply : Specification for 3.3V VCC supply.
- touchscreen-size-x : See touchscreen.txt
- touchscreen-size-y : See touchscreen.txt
- touchscreen-inverted-x : See touchscreen.txt
- touchscreen-inverted-y : See touchscreen.txt
- touchscreen-swapped-x-y : See touchscreen.txt
Example:
i2c@00000000 {
zet6223: touchscreen@76 {
compatible = "zeitec,zet6223";
reg = <0x76>;
interrupt-parent = <&pio>;
interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>
};
};
@@ -0,0 +1,34 @@
* Neonode infrared touchscreen controller
Required properties:
- compatible: must be "neonode,zforce"
- reg: I2C address of the chip
- interrupts: interrupt to which the chip is connected
- reset-gpios: reset gpio the chip is connected to
- x-size: horizontal resolution of touchscreen
- y-size: vertical resolution of touchscreen
Optional properties:
- irq-gpios : interrupt gpio the chip is connected to
- vdd-supply: Regulator controlling the controller supply
Example:
i2c@00000000 {
/* ... */
zforce_ts@50 {
compatible = "neonode,zforce";
reg = <0x50>;
interrupts = <2 0>;
vdd-supply = <&reg_zforce_vdd>;
reset-gpios = <&gpio5 9 0>; /* RST */
irq-gpios = <&gpio5 6 0>; /* IRQ, optional */
x-size = <800>;
y-size = <600>;
};
/* ... */
};