91 lines
2.4 KiB
C
91 lines
2.4 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (c) 2020 MediaTek Inc.
|
|
*/
|
|
|
|
#ifndef ITG1010_H
|
|
#define ITG1010_H
|
|
|
|
#include <linux/ioctl.h>
|
|
|
|
#define ITG1010_I2C_SLAVE_ADDR 0xD0
|
|
|
|
/* ITG1010 Register Map (Please refer to ITG1010 Specifications) */
|
|
|
|
#define ITG1010_REG_DEVID 0x75
|
|
#define ITG1010_REG_FIFO_EN 0x23
|
|
#define ITG1010_REG_AUX_VDD 0x01
|
|
|
|
#define ITG1010_REG_SAMRT_DIV 0x19
|
|
/* set external sync, full-scale range and sample rate, low pass filter
|
|
* bandwidth
|
|
*/
|
|
#define ITG1010_REG_CFG 0x1A
|
|
#define ITG1010_REG_GYRO_CFG 0x1B /* full-scale range and sample rate, */
|
|
|
|
#define ITG1010_REG_GYRO_XH 0x43
|
|
|
|
#define ITG1010_REG_TEMPH 0x41
|
|
|
|
#define ITG1010_REG_FIFO_CNTH 0x72
|
|
#define ITG1010_REG_FIFO_CNTL 0x73
|
|
#define ITG1010_REG_FIFO_DATA 0x74
|
|
#define ITG1010_REG_FIFO_CTL 0x6A
|
|
#define ITG1010_REG_PWR_CTL 0x6B
|
|
#define ITG1010_REG_PWR_CTL2 0x6C
|
|
|
|
/*ITG1010 Register Bit definitions*/
|
|
|
|
#define ITG1010_FIFO_GYROX_EN 0x40 /* insert the X Gyro data into FIFO */
|
|
#define ITG1010_FIFO_GYROY_EN 0x20 /* insert the Y Gyro data into FIFO */
|
|
#define ITG1010_FIFO_GYROZ_EN 0x10 /* insert the Z Gyro data into FIFO */
|
|
/* disable VDD level for the secondary I2C bus clock and data lines */
|
|
#define ITG1010_AUX_VDDIO_DIS 0x00
|
|
|
|
/* for ITG1010_REG_CFG */
|
|
/* 0x05 //captue the state of external frame sync input pin to insert into
|
|
* LSB of registers
|
|
*/
|
|
#define ITG1010_EXT_SYNC 0x03
|
|
#define ITG1010_SYNC_GYROX 0x02
|
|
|
|
/* for ITG1010_REG_GYRO_CFG */
|
|
/* set the full-scale range of the gyro sensors */
|
|
#define ITG1010_FS_RANGE 0x03
|
|
#define ITG1010_FS_1000 0x02
|
|
|
|
#define ITG1010_FS_1000_LSB 33
|
|
#define ITG1010_FS_MAX_LSB 131
|
|
|
|
#define ITG1010_RATE_1K_LPFB_188HZ 0x01
|
|
#define ITG1010_RATE_1K_LPFB_256HZ 0x00
|
|
|
|
#define ITG1010_FIFO_EN 0x40 /* enable FIFO operation for sensor data */
|
|
|
|
#define ITG1010_FIFO_RST 0x40 /* reset FIFO function */
|
|
|
|
#define ITG1010_SLEEP 0x40 /* enable low power sleep mode */
|
|
|
|
#define ITG1010_SUCCESS 0
|
|
#define ITG1010_ERR_I2C -1
|
|
#define ITG1010_ERR_STATUS -3
|
|
#define ITG1010_ERR_SETUP_FAILURE -4
|
|
#define ITG1010_ERR_GETGSENSORDATA -5
|
|
#define ITG1010_ERR_IDENTIFICATION -6
|
|
|
|
#define ITG1010_GYRO_ODR_400HZ 0x0A
|
|
#define ITG1010_GYRO_ODR_200HZ 0x0B
|
|
#define ITG1010_GYRO_ODR_100HZ 0x0C
|
|
|
|
#define ITG1010_BUFSIZE 60
|
|
|
|
/* 1 rad = 180/PI degree, MAX_LSB = 131, */
|
|
/* 180*131/PI = 7506 */
|
|
#define DEGREE_TO_RAD 7506
|
|
|
|
#ifdef CONFIG_CUSTOM_KERNEL_GYROSCOPE_MODULE
|
|
extern bool gyro_success_Flag;
|
|
#endif
|
|
|
|
#endif /* ITG1010_H */
|